Hisense is a famous brand in TV, and it is the go-to choice for people willing to buy a high-quality TV without breaking the bank. However, every electronic item encounters an issue, and there is no exception for Hisense TVs too! We have a few people who have witnessed Hisense TV won’t turn on red light flashes 6 times.
And we have planned to discuss the Hisense TV won’t turn on red light flashes 6 times issue and give you some real-time fixes for the problem. So read this article until the end so you won’t miss any critical information.
- Start With A Restart.
- Check The Power Cord.
- Go For A Power Cycle.
- Check Your TV Mode
- Examine Your Main Board
- Verify Your Internet Connection
- Check Your Sensors
- Update The Software
- Examine The LED Lights
- Inspect The T Con Board.
- Opt For A Hard Reset.
- Reach Your Support Service.
Start With A Restart.
There are more chances for temporary errors and glitches in your TV software; surprisingly, a simple restart may fix this instantly.
Here is the quick guide for a quick reboot, and I am sure it will take only a few minutes of your time.
- Keep pressing the “power” key until you find the TV light turning OFF
- Next, unplug your Hisense TV from the power source
- Wait for 2 minutes
- Finally, plug the TV back into the power source
Check The Power Cord.
The TV may not have a sufficient power supply if you have a damaged or faulty power cord. So due to the inadequate power, you may experience Hisense TV won’t turn on red light flashes 6 times.
How do you know if your power cord is in good condition?
- Inspect your cables and double-check whether the wires have cuts or damages.
- Get a new power cord from your neighbor and check whether the TV works well now.
Go For A Power Cycle.
The power cycle is one effective fix that resolves most of the problems in the device. A power cycle includes turning the TV OFF and ON, which is very easy.
To power cycle
- Turn off your TV
- Unplug the power cord from the backside of your TV
- Wait for 30 to 40 seconds
- Plug the power cord back in again
- Now turn ON your TV
Check Your TV Mode
If your TV is in standby mode, there is a probability of getting your Hisense TV won’t turn on and red light flashes 6 times. Hence cross-check whether your LED works appropriately. If your power light is responding to your remote control, but your TV is not turning ON, you can be sure that the issue represents that your TV is in standby mode.
To check this
- Head towards menu
- Then tap on settings
- Choose advanced system
- Now turn off the option “Power LED.”
Examine Your Main Board
Hisense TV won’t turn on red light flashes 6 times due to the faulty or damaged motherboard. There may be many causes for this main board or power board damage, and we list some.
- Unexpected power surge
- Fluctuating voltages
- Defective boards
- Damaged internal components
- Short circuit
- Overheating the TV
- Loose connections
- Defective capacitors
- Insufficient power supply
To fix the Hisense TV won’t turn on red light flashes 6 times issue; you can try.
- Resetting the TV.
- Besides handling voltage fluctuations and short circuits, install a voltage stabilizer.
- Replace the wires, cables, capacitors, and internal components if it is broken
- Tighten your connections inside the motherboard and powerboard
- Ensure that the power supply is sufficient
Verify Your Internet Connection
You may experience Hisense TV won’t turn on red light flashes 6 times even because of a poor or bad network connection. Therefore, check if there are any power deflection issues or modem errors.
Check Your Sensors
Suppose your sensors are damaged or have stopped working; you may experience a Hisense TV won’t turn on red light flashes 6 times. This may occur due to
- Usage of dirty sensors
- The remote is not configured correctly to the TV
- Blockage in the path between the TV and remote
- Defective remote control
- Damaged or dead batteries in the remote
The effective fix would be checking the manual for examining the sensor. And then replace the sensor with a new one. Once you replaced your sensor, power cycle the Hisense TV.
Also, we have other solutions if this is your case,
- Double-check that the remote control is configured correctly
- Use compressed air to remove even the minute dirt
- Prevent any blockages in the transmission path
- Replace the batteries and remote if necessary
Update The Software
Outdated software or firmware may barely affect the performance of your TV and sometimes even cause Hisense TV won’t turn on red light flashes 6 times.
Added that the regular updates increase the quality, performance, resolution, and even additional features for your Hisense TV. Therefore update your firmware and software whenever you are notified.
Examine The LED Lights
Usually, the LED strip in the TV unit has several LEDs. If any one of the LED lights gets burnt or damaged, you may get your Hisense TV won’t turn on red light flashes 6 times.
The root factors for the damage in the LED strips may be high electricity, short circuits, defective backlights, unexpected power surges, and voltage fluctuations. To fix this, check your LED lights one by one and replace them if there is any damage. Similarly, you can use a stabilizer if your area is prone to fluctuations.
Inspect The T Con Board.
A defective or damaged T Con board cause Hisense TV won’t turn on red light flashes 6 times. The T Con board in the TV is connected to the circuit board and the display panel.
Hence a defective board will cause damage to the display, and the TV will start malfunctioning. Besides, the cracks in the T Con board may be due to power outages, faulty internal components, defective capacitors, wrong or improper wire connections, damaged panels, short circuits, and misplaced connectors.
A factory reset or replacing the T Con board will help you eliminate this Hisense TV won’t turn on red light flashes 6 times problem. Furthermore, make sure you watch TV when there is a power surge and double-check that the T Con board has enough power supply.
Opt For A Hard Reset.
Don’t get stuck if the above way is not your cup of tea. Try hard resetting your TV; this may be your last choice.
For this, Press the menu button on your remote until you see all the indicators lighting up. Alternatively, you can try hard resetting without using your remote. Yes, by pressing the power button on your Hisense TV.
Note that resetting will restore your settings to the default configuration and delete all the files. But a hard reset will help you eliminate all the problems.
Reach Your Support Service.
Suppose you have failed in all the preceding methods; you should approach the customer service team as you have received a faulty product.
Additionally, you should enclose your Hisense TV model number, remote’s serial number, and date of purchase while contacting customer support. So that the Hisense team will check your warranty period and take immediate action for your Hisense TV won’t turn on and red light flashes 6 times issue.
If you are experiencing your Hisense TV Black Screen, here is How To Fix
Final Note On Hisense TV Won’t Turn On Red Light Flashes 6 Times
Nothing is unknown as we have a lot of resources on the internet today. So it is effortless to find solutions for your Hisense TV won’t turn on red light flashes 6 times issue.
We are not sure you will be fixing it even by trying the first step. Hence try testing with all the above fixes one by one, and we hope you can resolve the issue as soon as possible.